Storing kinetic energy in a flywheel allows for more efficient driving of electricvehicles. Research in this area is in progress at Uppsala University, where a flywheelwith magnetic bearings encased in a vacuum chamber is being constructed. To makethis possible methods for measuring the current through the electromagnets in thebearings and temperatures in the flywheel need to be developed. This has been thepurpose of this report. The current measurement resulted in a resistive method, andthe implementation of eight measurement circuits in the system.

The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.

The aim of the present study was to evaluate the effects of large amounts of straw in the farrowing pen on thermal regulation of the newborn piglet in different weight classes. 20 sows were given 15 kg of straw in the farrowing pen 2 days prior to until 7 days after parturition. A control group of 18 sows had no straw in the pen. 6 litters from each treatment were observed. Measurements of piglet body temperature were made at 0h, 2h, 4h, 8h and 24h after parturition. At ?8h? the body temperature of the piglets in the Straw group were significantly higher (P=0,0149) than the piglets in the Control group.

The use of silicon carbide (SiC) as a base material in power electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and high temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

In this final thesis a rough description of aluminium extrusion is made, the importance of temperature of both the raw material and the extruded profile for a good profile quality. The difficulty in controlling these temperatures are discussed and attempts to increase the control are described. The attempts are basically made by controlling the furnace that is heating the raw material. This is done in a manner that the raw material reaches its final temperature shortly before it is extruded. An IR-camera at the press can be used for profile Temperature measurements.

This thesis describes a method of measuring axial magnetic leakage flux in an operational hydropower generator. Axial magnetic leakage flux is the magnetic flux at the ends of a rotating generator, which goes through the stator parallel to the rotor axis. This flux can cause circulating currents in the stator iron, giving rise to losses, and can in the worst case overheat a generator, causing it to melt down. To measure the axial flux, and how it affects the generator temperature, a measurement system was constructed on behalf of Vattenfall. The system consists of search coil sensors and a signal-processing unit with amplifiers and active filtering.  To confirm the behaviour of the axial leakage flux and the functionality of the measurement system, a test installation was made.

The aim of this thesis is to improve the control of urea injection at the combined power and heating plant Framtidens Gärstad (FTG). Tekniska Verken i Linköping AB is the owner of the plant.The FTG plant consists of a boiler where garbage combustion is done. From the combustion nitrogen oxides are emitted. These nitrogen oxides are hazardous to the environment. To reduce the nitrogen oxides, injection of urea into the boiler is used.

This thesis deals with different methods for measuring moisture-related dimensional changes ofwood. Typically relative humidity is measured to determine if the ambient climate around anobject is harmful to it or not. Values between 40 to 65% RH are recommended for hygroscopicmaterials. To know how a wooden object actually reacts to changes in the surroundingenvironment requires methods that involve the object itself. Because of the wood anisotropy,differences in wood structure, finishes and other restraints, it is not always possible to predict themovements.This paper addresses various measurement methods, primarily methods that have been testedin the field of conservation, with examples of their use.

A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.

Background: Performance measurement as a management control tool has received considerable academic attention. As the number of inter-organisational relationships, such as customer-supplier relationships, increases, there is a new scope for performance measurement as a management control tool. In order for a company to assess the effectiveness of its supplier relationships it has to define, measure and evaluate variables that are critical for the success of the relationship. The role of management control, and thereby of performance measurement, has increasingly been discussed in theory. However, empirical research in this area is still somewhat limited.

More often consumers demand instant dry soup that can be prepared with a water temperature below 100o C, which is currently not possible, because the dry soup becomes too thin when using water with a lower temperature. In this study, various kinds of starch studies were made to optimize the starch used in the existing product to make it more viscous at both high and low temperatures. The result was that one of the two starches present in the existing product was retained by change in quantity as it contributed to important flavor parameters. The second was removed and replaced with a starch that made the product more viscous at lower temperatures. To find out if the new product differed from the existing product a viscosity measurement and a sensory paired preference test were made.

This study investigates three different methods for evaluating MOE,Modulus of Elasticity, in field measurements. The purpose is toinvestigate the possibility to use dynamic measurement methods infield measurements that hitherto (2010) has been performed with staticmethods. The objects of investigation are 20 glulam beams. The firstfield measurement took place in november 2007 and applied a staticmethod based on the standard SS-EN 408. The second measurement,described in this study, took place during summer 2010, and appliedstatic as well as dynamic methods.The MOE of wood is affected by a range different factors.

Aim: To examine the reaction of extreme preterm infants with regarding to body temperature and transepidermal water loss during skin-to-skin care according to Kangaroo Mother Care (KMC) during the infant?s first week of life. Method: This was a descriptive quantitatively designed study, which was a pilot study within the framework of a larger project. Nine children, with a median gestational age of 24.91 weeks, were examined by measuring body temperature (axilla and skin temperature) as well as transepidermal water loss before, during and after KMC. Results: The study showed that skin temperature tended to rise during KMC, especially for those children who were nursed with KMC for more than 60 minutes.

Flow measurement is one of the greatest challenges in order to calculate efficiency in hydropower. Most hydropower plants in Sweden use differential pressure methods for flow measurement. These methods are dependent on constant conditions in the waterways. A change in these conditions, like turbine improvements, prevents differential pressure methods to verify efficiency improvements. Since efficiency improvements can?t be verified by one measurement system, another method, which isn?t affected by changing conditions, can be used.

A number of studies in human medicine has documented positive effects of whole body vibration treatment in humans. The Vitafloor system, witch is based on treatment of horses with vibration, has the purpose to be used in training of healthy horses and as rehabilitation for horses with injuries in their musculosceletal system. The purpose of this study was to analyse what happens with a clinically healthy horse during treatment with Vitafloor. The methods used is mainly thermography before and after treatment, but also blood samples, measurement of rectal temperature, heart rate, clinical examination and observation of psychic reactions has been done. Statistic significant changes in skin temperature in hoofs and fetlocks of front legs has been observed after treatment with Vitafloor. Analyzing of the blood samples showed a tendency for decrease in Kalium, and two of the horses had changes in CK. No negative effect has been observed with the treatment of horses with Vitafloor, and the horses seems to like the treatment. .